Skip to main content

Learn 6 Easy Steps to Replace a Tip Top

Learn 6 Easy Steps to Replace a Tip Top

See how to repair and replace your rod’s tip top whether at home or on the water!

How to Repair a Tip Top on Your Fishing Rod

There’s a law out there that says anything that can happen to your rod’s tip top will happen, or something like that. The point is, accidents happen, especially with fishing equipment, and especially on the water.

Learning to repair the tip of your rod on the go could save a favorite rod, a fishing trip, or even a tournament paycheck.

First we will cover some tips to remove the old tip top, if the car door didn’t already do that for you… Then, in 6 simple steps, we will guide you through sizing and repairing your tip top to be good as new!

Remove the Old Tip Top to Start

Sometimes you don’t lose the tip of the rod or the tip top, and rather you lose only the insert ring. No problem!

Easy when done correctly, remove your tip top by whisking a small flame, such as a lighter or candle, back and forth under the tube of the tip top.

//content.osgnetworks.tv/infisherman/content/photos/Replacing-Tip-Top-770.jpg

Through a gentle heat, the tip top adhesive will melt then release from the rod blank, but remember to never twist it off. Pulling the tip top straight off of the blank will help avoid any additional complications.

//content.osgnetworks.tv/infisherman/content/photos/TwistRemove.jpg

The remaining steps will take you from a bare rod tip to being back on the water with a tip top and ready to fish.

//content.osgnetworks.tv/infisherman/content/photos/Remove.jpg

1. Identify the Tip-Top Style

Generally, tip-tops range from spinning and casting tops to fly and boat tops.

Different tip-tops are made for each fishing application, double check to make sure you chose the right design when ordering the replacement.

Don’t worry, we have them ALL!

2. Measure the Ring & Tube Size

Measured in millimeters, the ring size can either be determined by the outside diameter (OD) of the ring, also known as the eyelet, or the inside diameter (ID) of the tip-tops metal frame that holds the ring. Standard ring sizes for conventional rods are 6, 8, and 10 millimeters.

Recommended


For heavier fishing applications like saltwater rods, ring sizes can get as big as 16mm.

//content.osgnetworks.tv/infisherman/content/photos/Tip-Top-graphic.jpg

Considering both methods will give you the same measurement, it is primarily a matter of what you have available to measure. For instance, if you lost the entire tip-top then you can usually measure the ring size of the smallest guide and that will be an equal measurement.

Finding the tube size is dependent on either the inside diameter (ID) of the tip-top tube or the outside diameter (OD) of the blank’s tip. Tube sizes can get a bit more obscure because they are measured through a fraction and unlike ring sizes, the fraction is in inches instead of millimeters.

To make things interesting, the tube size is represented by 64ths of an inch.

The tube measurement you see when purchasing a tip-top is actually the numerator over 64ths of an inch. For example, common tube sizes range from 3.5 to 12, but remember this actually means they range from 3.5/64ths to 12/64ths of an inch.

Want a great tool to help measure tip tops and guides in seconds? Try the CRB Tip Top and Guide Sizing Gauge!

//content.osgnetworks.tv/infisherman/content/photos/MeasureTube.jpg
//content.osgnetworks.tv/infisherman/content/photos/ReallyReallyMeasureTube.jpg

When using the gauge, make sure you put the tip of the rod through the hole about the same depth as the length of the tip top tube.

Check out the image below for an example:

//content.osgnetworks.tv/infisherman/content/photos/ReallyMeasureTube.jpg

Whether you’re looking for the ring size, tube size, or guide measurements – it will be hard to find a resource as helpful as this gauge.

//content.osgnetworks.tv/infisherman/content/photos/TipTopKit_1_0001_TipTopGauge.jpg

Not only will tip top tubes fit onto the gauge’s pegs, but there are also pegs to size your guides too!

//content.osgnetworks.tv/infisherman/content/photos/Shop-Tip-Top-Guide-Sizing-Gauge.jpg

Once you have your tip top style and measurements, order your new tip top!

3. Heat Tip Adhesive, Schmear it, & Roll it

Next – open up your new tip top from Mud Hole, and take out your tip top adhesive and a lighter because its showtime.

Whisk the flame of the lighter over the end of the tip top adhesive and give it a few passes until it is visibly melting on the edge.

//content.osgnetworks.tv/infisherman/content/photos/HeatGlue.jpg

Now stay with us here… if you have a workshop table or a surface where you don’t eat dinner, use this method:

Schmear the melted end of the adhesive onto your surface like so.

//content.osgnetworks.tv/infisherman/content/photos/SmearIt.jpg

Give it one Mississippi to cool, and then quickly roll it up off the surface like well, a booger?

Continue to roll that adhesive until you’ve made a thin cylinder to fit inside the tube of your new tip top.

=//content.osgnetworks.tv/infisherman/content/photos/InsertAdhesive.jpg

4. Stick into Tube & Melt Adhesive

Take that adhesive and stick it right into the tip top.

Then, get your lighter and waft the flame underneath the tube of the tip top. Don’t just hold the flame on the tip top or you will leave scorch marks.

//content.osgnetworks.tv/infisherman/content/photos/HeatingTipTop.jpg

These can usually be cleaned off, but it’s also easily avoidable to begin with.

As the adhesive starts to melt again, quickly move on to the next step.

5. Twist Tip Top onto Rod Tip

Take the tip top and twist it down onto the rod tip.

//content.osgnetworks.tv/infisherman/content/photos/TipTopKit_1_0000_TwistRemove.jpg

Make sure you rod tip runs all the way into the tube of the tip top. If there is room on the inside of the tube between the rod tip and the tip top it could lead to another failure even after the adhesive cures.

6. Align Tip Top with Running Guides

Before the adhesive hardens, make sure you twist the tip top to align it with your running guides.

//content.osgnetworks.tv/infisherman/content/photos/LineUpGuides.jpg

Once aligned, let the adhesive cure for a minute or two and you’re ready to get back to fishing!

Check out Tip Top Repair Kits

When you’re on the water, you can’t exactly get a new tip top shipped to you in that moment. But instead, you can order our

Tip Top Repair Kits!

Order your repair kit based on the insert ring size if necessary, and the application styles. Each kit is sorted by application and includes 5 tip tops with realistic tube sizes in the increments that make sense for your rods.

For instance, most spinning and casting tip top tube sizes will range from 4.5 to 6.5 – meaning that particular kit would include: a 4.5, a 5.0, a 5.5, a 6.0, and a 6.5 inside.

//content.osgnetworks.tv/infisherman/content/photos/GrabTipTop.jpg

These kits also include Tip Top Cement for a sturdy bond on every rod tip.

Having multiple tube sizes available like this allows you to make speedy repairs on the water, so you can catch more fish and avoid wasting any time on worrying!

//content.osgnetworks.tv/infisherman/content/photos/Shop-Tip-Top-Repair-Kits.jpg



GET THE NEWSLETTER Join the List and Never Miss a Thing.

Recommended Articles

Recent Videos

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Gear

In-Fisherman Classics: Giant Snake River Sturgeon with Al Lindner

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Learn

In-Fisherman Classics: Sturgeon on the Colombia River with Al Lindner

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Learn

In-Fisherman Classics: Technical Carp Angling with Al Lindner

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Learn

In-Fisherman Classics: Dan Sura Tackles GIANT Texas Alligator Gar

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Destinations

In-Fisherman Classics: American Carp Tactics Vs. European

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Gear

In-Fisherman Classics: Giant Fish of North America

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Learn

Fishing Line Magical Management

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Learn

Downsize Crankbaits for Bigger Fall Walleyes with Capt. Ross Robertson

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Learn

Rigged Right for Precision Walleye Trolling with Capt. Ross Robertson

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Destinations

In-Fisherman Storyline: Roadtrip Edition at Andy Myer's Lodge on Eagle Lake

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Learn

In-Fisherman Classics: Ice Fishing for Lake Winnipeg Walleyes

In-Fisherman Editor-in-Chief joins Bret Alexander to chase big whitefish in Green Bay. Why whitefish? They are abundant,...
Gear

In-Fisherman Classics: Ice Fishing for Whitefish in Door County, Wisconsin

In-Fisherman Magazine Covers Print and Tablet Versions

GET THE MAGAZINE Subscribe & Save

Digital Now Included!

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW THIS MONTH'S ISSUE

Buy Digital Single Issues

Magazine App Logo

Don't miss an issue.
Buy single digital issue for your phone or tablet.

Get the In-Fisherman App apple store google play store

Other Magazines

See All Other Magazines

Special Interest Magazines

See All Special Interest Magazines

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Get the top In-Fisherman stories delivered right to your inbox.

Phone Icon

Get Digital Access.

All In-Fisherman subscribers now have digital access to their magazine content. This means you have the option to read your magazine on most popular phones and tablets.

To get started, click the link below to visit mymagnow.com and learn how to access your digital magazine.

Get Digital Access

Not a Subscriber?
Subscribe Now

Enjoying What You're Reading?

Get a Full Year
of Guns & Ammo
& Digital Access.

Offer only for new subscribers.

Subscribe Now

Never Miss a Thing.

Get the Newsletter

Get the top In-Fisherman stories delivered right to your inbox.

By signing up, I acknowledge that my email address is valid, and have read and accept the Terms of Use